• Products
  • 5215512290 Toyota SUPPORT, REAR BUMPER SIDE, RH

5215512290 Toyota SUPPORT, REAR BUMPER SIDE, RH, Price: 16.28$, Weight: 0.034kg

    • Make Number Name Availability Weight, kg Ship in, Days Price

    Toyota

    5215512290

    SUPPORT, REAR BUMPER SIDE, RH

    		 5

    0.034

     Dispatch 24h

    16.28$
     

    Originals

    Make Number Name Availability Weight, kg Processing, days Price  
    Toyota
    5215512290 
    SUPPORT, REAR BUMPER SIDE, RH
    		55
    0.039
    2-3
    13.57$
     
    HABASHI
    5215512290 
    R. BUMPER BRACKET
    		0
    0.039
    4-5
    2.42$
    		 Not Available

    Compatibility

    DescriptionModelOptionsProd PeriodDiagram
    ZZE12#ZZE122R-GEPGKNATM,MTM: AUTOMATIC TRANSMISSION; NO. Of Doors: 4-DOOR; Driver's Position: RIGHT-HAND DRIVE VEHICLES; Body: SEDAN; Grade: GSX TYPE; Engine: (1ZZFE) 1800CC 16-VALVE DOHC EFI; Destination: SOUTH AFRICA08.2004 - 07.2007 View
    DescriptionModelOptionsProd PeriodDiagram
    CDE120,NDE120,ZZE12#ZZE120L-AEMNKWATM,MTM: MANUAL TRANSMISSION; Driver's Position: LEFT-HAND DRIVE VEHICLES; Body: SEDAN; Grade: SOL TYPE; Fuel Induction: HIGH EFFICIENCY TWIN CAM; Gear Shift Type: MTM, 5-SPEED FLOOR SHIFT; Engine: (4ZZFE) 1400CC 16-VALVE DOHC EFI10.2001 - 10.2006 View
    DescriptionModelOptionsProd PeriodDiagram
    CE120,NZE12#,ZZE12#ZZE122R-AEPNKQATM,MTM: AUTOMATIC TRANSMISSION; Driver's Position: RIGHT-HAND DRIVE VEHICLES; Body: SEDAN; Grade: ULTIMA TYPE; Engine: (1ZZFE) 1800CC 16-VALVE DOHC EFI; Destination: AUSTRALIA10.2001 - 02.2007 View
    DescriptionModelOptionsProd PeriodDiagram
    CE121,NZE12#,ZZE12#NZE121-AEPNKATM,MTM: AUTOMATIC TRANSMISSION; Body: SEDAN; Grade: X TYPE; Gear Shift Type: ATM, 4-SPEED FLOOR SHIFT; Engine: (1NZFE) 1500CC 16-VALVE DOHC EFI08.2000 - 09.2006 View

    Rear Right Bumper Side Bracket – precise fit for clean body lines ✅

    This OE-spec support secures the right-hand corner of the rear bumper cover to the body. It is needed to keep panel gaps even, stop corner sagging, and maintain a quiet, rattle-free ride. After small parking impacts, curb scrapes, or aged clips, the bumper can loosen; replacing this bracket restores factory alignment and durability.

    How it works

    The bracket locks the bumper cover using molded locating tabs and clip rails, then anchors to the quarter panel via factory bolt points. By spreading corner loads across multiple mounts, it stabilizes the bumper edge, resists flex, and keeps the cover seated during vibration and temperature changes. Impact-resistant polymer ensures light weight, corrosion-free service, and consistent clamp force.

    What happens if it’s broken ⚠️

    Expect a droopy bumper corner, growing gaps, and creaks or rattles over bumps. The cover may pop out at the wheel arch, scrape paint on the quarter panel, and allow dirt or water behind the bumper. Left unfixed, strain transfers to other retainers, risking cracked tabs and higher repair costs.

    Install notes ️

    Direct bolt-on to factory holes—no drilling. Transfer good clips or replace damaged ones, seat the cover fully on the rails, then tighten fasteners evenly. “Right-hand” means passenger side on LHD cars. Always inspect the opposite bracket for wear.

    Compatibility

    • Corolla (S.africa)
    • Corolla Sed/Wg
    • Corolla/Altis Sed/Wg
    • Corolla/Fielder